Showing results: 16 - 30 of 86 items found.
-
iWave Systems Technologies
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
iWave Systems Technologies
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
iWave Systems Technologies
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
68ARM1 -
North Atlantic Industries
NAI’s 68ARM1 is a 3U VPX ARM® Cortex®-A9-based, Single Board Computer (SBC) that can be configured with up to three smart function modules. Ideally suited for rugged defense, commercial aerospace, and industrial applications, the 68ARM1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
EverythingPCB
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Acculogic, Inc.
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
Circuit Check, Inc.
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Versi-Traq -
Automatiq Measurement Systems
A complete Ready-to-Wire Test Fixture including drilling, installed Pogo Pins, and board location hardware is available. Complete the Request for Quote form and send it to Automatiq for a fixed price quotation for a Ready-to-Wire test fixture for your board. We will need Gerber files for the board, a Test Point List with some way to relate the Test Points to the Gerbers, and a Sample Board populated as it will be tested in order to get started.
-
UWE Electronics
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Circuit Check, Inc.
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
HW Test
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Protector Adjustable Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Protector Edge Press Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Protector Press Rods Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Test Head Engineering, LLC
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
